E-Rustler

All Products proudly made in the U.S.A.

REM Bandit / Rustler Chassis

Machined out of Billet 6061-T6 Aluminum

1/4" Thick to handle extreme abuse

Weighs only 4oz more than stock chassis (11oz)

Machined with completely flat bottom to eliminate snags going
over rocks.

Machined pocket for receiver protecting it from damage and
debris

Chassis contour matches the stock body perfectly for a show
finished look

REM Battery hold-downs are included offering a secure place
to hold the battery and ESC.

All mounting hardware included

Machined pocket for after-market power switches (Castle and
Novak ESC's)

Uses Roll-Form Taps making threads 60% stronger than
standard threads.

REM 1060 $65.00

NEW! REM Transmission Case

Made from Aircraft Quality Aluminum (6061-T6-511)

CNC Machined for accuracy and strength

"One-Piece Design" of the rear arm mounts for
strength

Provides protection for your motor against rear
impacts

Bolts up to stock wheelie bar mount without
modification

Precision designed for perfect gear mesh

The entire Transmission Case works as a large heat-
sink significantly reducing motor temperatures.

Includes all fasteners for installation

Uses Roll-Form Taps making threads 60% stronger
than standard threads.

UPDATE: Now uses M4 fasteners for the Rear Arm
Mounts

Weighs 5 oz.

Rem 1050 $62.00

REM Front Shock Tower

Machined out of Billet 6061-T6 Aluminum.

Will work with any shock up to 1" thick which
allows the use of T-Maxx shocks.

.200" (5mm) Thick to handle Extreme Abuse.

Designed to work with stock or after-market front
bulkheads.

24 shock mount locations and 10 camber link
mount locations for the ultimate in tuning your
suspension.

Billet Aluminum shock standoffs.

All mounting hardware included

Uses Roll-Form Taps making threads 60%
stronger than standard threads.

REM 1010 $18.00

REM Rear Shock Tower

Machined out of Billet 6061-T6 Aluminum.

One Piece Design to maximize Strength

Works with bandit spoiler support allowing the
use of the bandit or other similar spoiler.

Will work with any shock up to 1" thick which
allows the use of T-Maxx shocks.

.200" (5mm) Thick to handle Extreme Abuse.

Designed to work with stock or after-market
Transmissions and Chassis.

20 shock mount locations and 4 camber link
mount locations for the ultimate in tuning your
suspension.

Billet Aluminum shock standoffs.

All mounting hardware included

Uses Roll-Form Taps making threads 60%
stronger than standard threads.

Allows the XL-5 ESC to mount directly to the
tower for optimum cooling

REM 1020 $27.00

REM Front Bulkhead

Made from Billet 6061-T6 Aluminum for strength and
light weight.

Weighs only 1.6 oz

Perfect fit with stock or after-market parts

Uses Roll-Form Taps making threads 60% stronger
than standard threads.

REM 1090 $27.00

REM Front Suspension Arms

Made from Billet 6061-T6 Aluminum for strength
and light weight.

Perfect fit with stock or after-market parts

Stock Length

All hardware included for installation including
stainless steel hinge pins and retaining rings.

weighs only 1 oz per arm

REM 1070 $21.00

REM Rear Suspension Arms

Made from Billet 6061-T6 Aluminum for strength
and light weight.

Perfect fit with stock or after-market parts

Stock Length

All hardware included for installation including
stainless steel hinge pins and retaining rings.

weighs only 1.4 oz per arm

REM 1080 $24.00

REM-1120 Rear Bearing Carriers

An additional hole was added to give more
clearance forthe drive shaft when the
suspension is at "full droop" (as pictured)

Low-Center-Of-Gravity Design allows you to
lower your truck an addition 5 mm over stock

Made from Billet 6061-T6 Aluminum for strength
and light weight.

Perfect fit with stock or after-market parts

Weight 0.4 oz/pair

REM-1120 $20.00